SMC串行傳送系統，EX120-SCS1

電話：O21-3952 9829/3O-8O1O
傳真：O21-6O83 1959
手機：189 1857 2467
Q：125 5O9 6653
聯系人：張海情
郵箱：8010@shqiantuo.com.cn

串行傳送系統   EX
一體型／輸出對應
系列/CAD 防護等級 通信協議 適合閥
EX120  IP20 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) SV1000,2000,3000,4000 VQ1000,2000
EX121  IP20 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) SY3000,5000
EX122  IP20 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) SY3000,5000
EX123  IP65 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) VQ2000,4000,5000
EX124  IP65 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) VQ2000,4000,5000
EX126  IP67※1 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) SV1000,2000,3000 VQC1000,2000,4000
EX140  IP20 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) SZ3000,SQ1000,2000
EX180  IP20※2 DeviceNetTM CC-Link 歐姆龍(CompoBus/S) SUNX(S-LINK) NKE (省配線系統) SJ2000,3000
※1 只對應CC-Link
※2 只對應CC-Link 、DeviceNetTM

串行傳輸系統，可控制多個電磁
通過只使用從PLC的通信線路的閥
通信模塊（主模塊）或它可以讀取
來自各種傳感器的信號。此系統也可以被稱為
“現場總線系統”。
接線線圈的每一個電磁閥，一個接一個，輸出
在PLC上的單元被稱為“并行布線”。使用在每個閥
需要連接。因此，根據布線
在使用電磁閥或傳感器的數量是必需的。
在Si單元是一個裝置，可以控制電磁閥
通過串行通信。
輸出數是多少的電磁閥或輸出
是可以控制的設備。
輸入數量等各種傳感器的數目
自動開關，壓力開關等可連接的。
輸出到控制裝置，用于打開/關閉
電磁線圈。
輸入/輸出是指ON-OFF控制的能力
（輸出）的電磁閥，以及讀取（輸入）的
的傳感器信號，如從一個自動開關或壓力
切換。
議定書裝置的串行數據被發送和/或接收在
根據命名規范。
開放式網絡意味著已經取得了一個標準，
公共和被廣泛接受。
綜合型是指SI單位和電磁閥
歧管集成。 SI單位有必要為每
協議。
分散型指的GW（網關）
的系統。
從該網關，電磁閥的歧管和所述
輸入設備可位于遠程。更換
網關使之間的各種變化
協議。
術語表
外殼被評為使用的IP（國際
保護）標準（IEC60529），專注于
防止灰塵或水。
IP20：防止手指進入機箱，但
沒有專門針對水。
IP65：防止灰塵進入機箱，而不是
股水柱從四面八方很大的影響。
IP67：防止灰塵進入機箱
在一個特定的壓力和時間浸泡在水中。
閥接口之間的連接
SI單位和電磁閥的歧管。
插件：連接器上的SI單位和
電磁閥的歧管直接插入
相互轉化。
插頭引線：SI單位和電磁線圈
與電線的連接
連接器。
扁平電纜：SI單位和電磁
閥門歧管相連
連同扁平電纜
有MIL連接器。
術語表
集成型和分散型
酒吧股票型（毛重系統）和堆疊式
機箱閥接口
酒吧股票類型由
歧管鋁基地
固定數目的歧管站。
堆疊的類型由
紙盒基座歧管或tierod的的
這兩個基地歧管
允許增加/降低
站的數量容易。

SMC串行傳送系統，EX120-SCS1

A serial transmission system can control multiple solenoid
valves by using only the communication line from the PLC’s
communication module (master module) or it can read the
signal from the various sensors. This system can also be called
a “Fieldbus system”.
Wiring the coil of each solenoid valve, one by one, to the output
unit on the PLC is called “Parallel wiring”. Each valve in use
needs to be connected. Therefore, wiring in accordance with
the number of solenoid valves or sensors in use is required.
A SI unit is a device which can control the solenoid valve
through serial communication.
Number of outputs is the number of solenoid or output
devices that can be controlled.
Number of inputs is the number of various sensors such as
an auto switch, pressure switch, etc. that can be connected.
Output refers to the control device for turning on/off the
solenoid coil.
Input/Output refers to the ability for ON-OFF control
(output) of a solenoid valve, as well as the reading (input) of
a sensor signal, such as from an auto switch or pressure
switch.
Protocol means the serial data is sent and/or received in
accordance with a named specification.
Open network means a standard that has been made
public and is widely accepted.
The integrated type means the SI unit and solenoid valve’s
manifold are integrated. An SI unit is necessary for every
protocol.
The decentralized type refers to the GW (Gateway)
system.
From the Gateway, the solenoid valve’s manifold and the
input devices can be located remotely. The replacement of
the Gateway enables changing between the various
protocols.
Glossary of terms
The enclosure is rated using the IP (International
Protection) standard (IEC60529) which focuses on
protection against dust or water.
IP20: Protection against fingers entering the enclosure but
not specifically against water.
IP65: Protection against dust entering the enclosure and not
greatly affected by jets of water from all directions.
IP67: Protection against dust entering the enclosure and
immersion in water at a specific pressure and time.
The valve interface is the connection between
the SI unit and the solenoid valve’s manifold.
Plug-in: The connector on the SI unit and the
solenoid valve’s manifold directly plug
into each other.
Plug lead: The SI unit and the solenoid coil are
connected with wires having a
connector.
Flat ribbon cable: The SI unit and solenoid
valve’s manifold are connected
together with a flat ribbon cable
having a MIL connector.
Glossary of terms
Integrated and Decentralized type
(GW system) Bar stock type and Stacking type
Enclosure Valve interface
The bar stock type consists of a
manifold base made of Aluminum with
a fixed number of manifold stations.
The stacking type consists of a
cassette base manifold or a tierod
base manifold both of which
allow increasing/decreasing of
the number of stations easily.

SMC串行傳送系統，EX120-SCS1

產品留言

標題

聯系人

聯系電話

內容

驗證碼

點擊換一張

注：1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!
2.如有必要,請您留下您的詳細聯系方式!